Daewoo Nexia

since 1994 of release

Repair and car operation


Deu Neksiya
+ Maintenance instruction
+ Maintenance
+ Engine
+ 3. Engine (two top camshafts)
+ cooling System
+ Toplevnaya and exhaust systems
+ Electric chain
+ 7. Ignition system
+ 8. Electronic control unit and sensors
+ Transmission
+ 10. Five-speed transmission and main RPO MM5 broadcast
+ 11. Automatic Transmission
+ Steering
+ Running gear
+ 14. Forward suspension bracket
+ 15. Drive of forward wheels
- 16. Back suspension bracket
   16.2. General description
   16.3. Maintenance and repair
   16.4. Check of size of forces of a friction in a suspension bracket
   16.5. Bearings of wheels
   16.6. Shock-absorber
   16.7. Stabilizer
   16.8. Springs
   16.9. Plugs of hinges of a back suspension bracket
   16.10. Back suspension bracket assembled
   16.11. Nave
+ Brake system
+ Body
+ Heating, ventilation
+ Electric equipment


8128da4b



16.9. Plugs of hinges of a back suspension bracket
GENERAL INFORMATION

Installation and plug dismantle from an eye of the lever of a back suspension bracket

AND. TO CUT THE HACKSAW GROOVES UNDER FACE LEDGES OF THE WASHER OF DC45001
CENTURY. AT INSTALLATION TO COMBINE ARROWS ON DETAILS OF J29376-1 HJ29376-11 OF THE ASSEMBLY ADAPTATION WITH THE LABEL AT THE END FACE OF THE EYE OF THE LEVER
PAGE. EYE OF THE LEVER OF THE BACK SUSPENSION BRACKET
22. PLUG OF THE HINGE OF THE LEVER OF THE BACK SUSPENSION BRACKET
26. LEVER OF THE BACK SUSPENSION BRACKET


To remove or disconnect

It is necessary to replace at each dismantling at once both plugs.

PERFORMANCE ORDER
1. To lift the car and to fix as appropriate.
2. To lift one of suspension bracket levers by means of a hydraulic jack and a suitable assembly support. To remove a bolt 8 and a nut 9.
3. To substitute a hydraulic jack under the second lever and to remove shock-absorber 7 fastening.
4. To lower a little hydraulic jack and to dismantle a spring 28 and the top elastic ring 29.
5. To lift it is a little lever a hydraulic jack and again to attach the shock-absorber 7 to a beam the 26th bolt 8.
6. To execute operations 3,4 and 5 on other party of the car. To arrange a hydraulic jack in the middle under a beam of the 26th suspension bracket.
7. Fastenings to the bottom of the Body of brake pipelines. To place brake hoses and cables of the parking brake in deepening of the bottom of the Body.
8. A bolt 23 and a nut 21 from an arm on the Body bottom. If necessary to use a screw-driver as the lever to press a hinge eye.
9. To lower it is a little beam 26 back suspension brackets and to fix a bolt the 23rd earring from set KM-158 in an arm of the hinge of a back suspension bracket. For simplification of dismantle of plugs to heat up eyes of levers to temperature 50–75 ° S.Nagrev to make hot air from a pneumatic network.
10. For plug dismantle from an eye of the lever to execute the following operations.
10а. To establish the KM-158 adaptation on a lever eye with the plug 22.
10б. To put on a bolt entering into assembly set KM-158, a washer with face ledges, to insert a bolt into a plug opening, then to put on it a persistent washer.
10в. To rest a stripper washer against an end face of the plug 22 and to screw on a bolt a nut.
Prevention

To cut through a hacksaw two grooves at an end face of the old plug 22 under ledges of a washer of a stripper.

10г. Rotating a KM-158 adaptation bolt, выпрессовать the plug from a lever eye.

To establish or attach

Plug orientation at installation

 AND. CORNER 45±5

22. PLUG OF THE HINGE OF THE LEVER OF THE BACK SUSPENSION BRACKET

PERFORMANCE ORDER
1. For plug installation in an eye of the lever to execute the following operations.
1а. To establish the KM-158 adaptation on the suspension bracket lever.
1б. To prepare and partially to assemble the assembly KM-158 adaptation.
1в. To establish the new plug 22 on a bolt, previously having inserted it into an eye opening. To turn the plug in specified fig. Plug orientation at installation situation concerning a lever eye. To expose arrows on KM-158 adaptation details according to a face label, see fig. Installation and plug dismantle from an eye of the lever of a back suspension bracket.
1г. To screw a nut on a KM-158 adaptation bolt.
1д. Rotating a KM-158 adaptation bolt, to press the plug in a lever eye. At the correct installation the back end face of the plug should settle down aflush with a lever eye.
2. To remove earring KM-158 from an arm of a suspension bracket and to establish on the opposite side of the car.
3. To dismantle old and to press the new plug in the second lever of a suspension bracket, operating similarly.
4. To raise a beam of a back suspension bracket by means of a hydraulic jack and to connect eyes of levers to suspension bracket arms bolts 23. To screw nuts 21. To lower a jack.
5. To establish the bottom buffer of a spring 27 on the lever, the top elastic ring 29 in a glass of the Body and a spring 28.
6. To lift a hydraulic jack the lever of a suspension bracket and to connect to the lever the bottom eye of the shock-absorber 7. To lower a jack, to establish a spring 28 and the shock-absorber 7 on the opposite side of the car, operating similarly. To lower the car.
7. To tighten bolts of fastening of a beam of a back suspension bracket in such position of levers which corresponds to a static course of a suspension bracket at the equipped mass of the car.